Product Details:
Payment & Shipping Terms:
|
Product Name: | Kaishan Rock Drill | Power Type: | Pneumatic,air Powered |
---|---|---|---|
Condition: | New | Weight: | 24-28kg |
Machine Type: | Drilling Tool | Applicable Industries: | Energy & Mining,Construction Works ,Building Material Shops,Retail |
High Light: | Air Leg Rock Drill Jack Hammer,Air Compressor Air Leg Rock Drill |
Pneumatic Power Tools YT24 YO18 Air Leg Rock Drill Jack Hammer For Air Compressor
YT24 is a kind of heavy and powerful rock drilling machinery with low air consumption.
Mainly used in construction sites, various types of mines, railways, water conservancy construction and national defense construction areas for drilling operations.
The product possesses practicability and value of popularization, which is available for all rock formations.
Item No.
|
HY18
|
YO18
|
Y19A
|
YO20
|
YT24
|
Rock Hardness
|
F=6-20
|
F=6-20
|
F=6-20
|
F=6-20
|
F=6-20
|
Piston Stroke
|
50mm
|
50mm
|
54mm
|
52mm
|
64mm
|
Cylinder Diameter
|
58mm
|
58mm
|
65mm
|
64mm
|
70mm
|
Working Pressure
|
0.4Mpa
|
0.4Mpa
|
0.4-0.5Mpa
|
0.4Mpa
|
0.5Mpa
|
Air Consumption
|
1.4m3/min
|
1.4m3/min
|
2.2-2.58m3/min
|
1.7m3/min
|
2.6m3/min
|
Drill Pipe Size
|
B22*108mm
|
B22*108mm
|
B22*108mm
|
B22*108mm
|
B22*108mm
|
Weight
|
18kg
|
21kg
|
19kg
|
21kg
|
27kg
|
Package Size(mm)
|
590*280*180
|
590*280*180
|
600*534*106
|
590*280*180
|
740*310*220
|
air leg
|
FT100
|
FT100
|
FT100
|
FT100
|
FT140
|
1. ratchet
2. valve cover
3. valve group
4. nuts
5. piston
6. cylinder block
7. guide sleeve
8. muffler cover
9. bushing
10. valve
11. positioning pin
12. ratchet grip
13. spiral rod
14. tower spring
15. air end
16. turning sleeve
17. brad
18. spring pad
19. brazed spring
20. brazed bolt
21. brazed
22. spline nuts
23. non-metailc hex nuts
24. long screw
25. contorl valve
26. water needle
27. gas needle
28. big gland
29. handle body
30. expansion valve
31. pressure regulator
32. control handle
33. left handle
34. elastic ring
35. small gland 36. long screw nuts 37. steel snap ring 38. tracheall elbow 39. trigger 40. directional valve 41. spring 42. water pipe elbow 43. steel snap ring 44. fastening pin 45. water injection valve body 46. steel snap ring 47. spring cover 48. water injection valve 49. right handle 50. plastic handle 51. sealing ring 52. spring 53. water needle gland 54. pad 55. gas needle pad 56. spring 57. postioning pin 58. ring seal 59. pad 60. O -ring seal 61. O -ring seal 62. O -ring seal 63. O -ring seal 64. hose clamp 65. flexible pin 66. standard spring washer 67. hexagon thin nut 68. tracheal nut |
Analysis on the use of rock drills
1. The machine has anti-rust oil when it leaves the factory. It should be disassembled and cleaned before use. When reassembling, the mating surface should be lubricated with lubricating oil, and the trolley should be run for trial operation.
2. When connecting the gas and water pipes, the debris in the pipes must be blown to avoid entering the machine and affecting the normal operation of the machine; when drilling, keep the water pressure 0.1-0.15MPA lower than the air pressure. So as not to let the flushing water enter the inside of the body, affect the lubrication, and bring in the sundries.
3. Before ventilation and water, carefully check whether the connection parts are safe and reliable to avoid loosening and hurting people.
4. Fill the oiler with oil before starting the machine, and it is strictly forbidden to operate without lubrication.
5. When using on-site with super gas, lubricating oil with low flash point and easy to ignite cannot be used, and the machine is not allowed to run idly to prevent explosion accidents.
6. Adjust the oil valve, it is advisable to add oil once an hour.
7. When working, pay special attention to the sudden breakage of the drill rod; pay attention to prevent being pinched between the rock drill and the air leg.
8. When the machine is finished, the water source should be turned off first, and then run for a while to remove the accumulated water in the machine and prevent rust.
9. The machine that is used continuously should be maintained regularly, the stolen goods in the machine should be removed, the damaged parts should be replaced, and the hidden troubles should be removed.
10. If the used machine is stored for a long time, it must be disassembled and washed, oiled, and placed in a cool and dry place.
11. Air legs and oiler are controlled by the safety standard. Users should choose the above-mentioned parts (components) of our company to match with the host.
12. When the pneumatic rock drill is working, noise, vibration and dust will be generated, please pay attention to the protection of the operator, and need to wear muffler earmuffs, etc.
19. If the oiler housing has cracks, please replace it in time.
Contact
Ella Chen
WhatsApp/wechat: +8615167050487
Mail: sale68@jugonggroup.com
Contact Person: Mrs. Christina
Tel: +8615905700688
Fax: 86-570-3865123